Configure Wireless Access for the Brother HL-2280DW Multi-Function Laser Printer

7:02 pm Mac OS X, Windows

I scored a great deal on two Brother HL-2280DW Wireless Laser Printers (with scanner functions) during Thanksgiving break. Once I got the printers and tried to configure them for wireless, I found that Brother’s wireless configuration options were lacking and in some cases, didn’t work at all.

Unfortunately, the Ethernet connectivity on one of the printers was broken; worse, that was the printer I picked first to configure. After wasting half the weekend, I thought I would document how I finally went about configuring the wireless access for the Brother HL-2280DW printer and adding it to my Windows and Mac OS X machines. Hopefully, the steps below will help you with your Brother printer woes.

Note: The instructions below will work for other Brother wireless printers. I’ve also tried them successfully with Brother HL-2170W, HL-2270DW, and MFC-7860DW printers.

Configure Wireless Access With Ethernet Connection and Web Interface

Note: The WPS and “WPS with Pin” setup did not work with my Cisco Linksys E1000 router. And while the printer allowed me to manually input the SSID and passphrase using the up/down arrows, the printer’s LCD only displayed the first 10-12 digits of the passphrase making it impossible to input the rest! Because I dislike using the USB method (which required installing, uninstalling, and then re-installing software), I decided that using the printer’s Ethernet connection and web interface was the best solution.

  1. Before we start, you will need to know the following info concerning your wireless network (check your wireless router’s configuration):
    • Network ID (SSID)
    • Channel Number (usually 3, 7, or 11)
    • Authentication Method (WEP, WPA or WPA2)
    • Encryption Mode (TKIP or AES)
  2. Follow the included Brother “Start Here” manual to prepare the printer for operation.
  3. Before turning on the printer, connect it to your wireless router by Ethernet cable.
  4. After the printer is on, we will need to find its assigned IP address:
    • Look it up on the printer:
      1. Press the Menu button to the right of the printer’s LCD and you will see “1. General Setup” menu item show up. You might need to press the Menu button twice sometimes. (Do not select the “1. General Setup” item.)
      2. Select the following menu items by pressing the up/down arrows and clicking on the OK button:
        • 4. Network
        • 1. Wired LAN
        • 1. TCP/IP
        • 2. IP Address
    • Alternatively, you can browse to your wireless router’s web interface and look at the list of connected DHCP clients.
  5. Browse to the printer’s assigned IP address to access its web interface.
  6. Configure the printer to enable toner save mode and to allow printing even if the toner is low:
    1. Click on “General Setup” at the top.
    2. You will be prompted for the user/password. Input the default: admin/access.
    3. Set the following options:
      • Toner Save: On
      • Replace Toner: Continue
    4. Click on the Submit button
  7. Configure the wireless network access:
    1. Click on “Network Configuration” link at the top.
    2. Click on the “Configure Wireless” link near the bottom of the page.
    3. Configure the following options:
      • Communication Mode: “1) Infrastructure Mode”
      • SSID: [input your wireless ID]
      • Channel: [input the wireless channel]
      • Authentication Method: WPA/WPA2-PSK (usually)
      • Encryption Mode: AES (usually for WPA2)
      • Passphrase: [input your wireless password]
    4. Click the Submit button.
    5. Answer Yes to “Would you like to enable the wireless interface?”.
    6. You will get a message to unplug the Ethernet cable. The printer will reboot and then print a page indicating whether the wireless connection succeeded or not.
  8. If the wireless connection didn’t succeed, then connect the Ethernet cable and repeat from step #4. Usually, the wireless router will give the printer the same IP address.
  9. If you are totally lost, you can reset the printer configuration by doing the following:
    1. Click on the Menu button next to the printer’s LCD.
    2. Select the following with the up/down arrows and the OK button:
      • 1. General Setup
      • 5. Reset
      • 2. All Settings
    3. Hit the Up arrow to Reboot.

Mac OS X: Add Printer, Set Toner Save Mode, and Scan

To add the printer on Mac OS X, do the following:

  1. Open up System Preferences.
  2. Click on “Print & Fax” under Hardware.
  3. Click the Plus button underneath the list of printers on the left.
  4. Bonjour should detect the printer and you will see “Brother HL-2280DW” listed.
  5. Select it and the “Print Using:” field will populate with “Brother HL-2280DW CUPS” driver.
  6. Click the Add button.
  7. The Brother HL-2280DW should show up on the list of Printers. To make it the default printer, double-click on it and select “Set default printer”.

To configure Mac OS X to use Toner Save Mode by default:

  1. Browse to the local CUPS driver web interface running on your machine. (You may be asked to run “cupsctl WebInterface=yes” in the Terminal application to enable the CUPS web interface.)
  2. Click on the Printers tab to the top-right.
  3. Click on the “Brother_HL_2280DW” printer in the list.
  4. Click on the Administration drop-down list box and select “Set Default Options”.
  5. Change “Toner Save Mode” to be “On”.
  6. Click on “Set Default Options” button.
  7. If you are prompted for a user/password, input your Mac OS X login username and the administration password.

The built-in way to do a scan on Mac OS X:

  1. Open up System Preferences.
  2. Click on “Print & Fax” under Hardware.
  3. Select the printer.
  4. Click on the “Scan” tab.
  5. Click the “Open Scanner…” button.
  6. Click “Show Details” for more options like output format and location.
  7. Make your selections and click on the “Scan” button.
  8. The scan will be taken and saved to the “Pictures” folder by default.

Windows XP and 7: Add Printer, Set Toner Save Mode, and Scan

To add the printer on Windows, do the following:

  1. Download the latest Brothers HL-2280DW printer software (it is the same file for Windows XP, Windows 7 32-bit, and Windows 7 64-bit and is named “HL-2280DW-inst-B1-usa.EXE”).
  2. Run the downloaded installation executable.
  3. Select “usa” for language. Click OK.
  4. Select “Wireless Network Connection” and check “Custom Install”.
  5. Take the default for “Change the Firewall port settings…”. Click Next.
  6. Take the default selected features (all are selected) and click Next.
  7. I usually select “No, I don’t want to register this PC to ‘Scan To’ button”; however, feel free to select Yes. (I think this option is so when you press the Scan button on the printer, it will send the image to this computer.) Click Next.
  8. On Windows XP:
    1. Keep the “Search the network for devices…” selected and click Next.
    2. Select the found Brother printer (the node name looks like “BRxxxxxxxxxx”) and click Next.
  9. On Windows 7, the printer detection doesn’t work so you will select either “Specify your machine by address” (IP address) or “Specify your machine by name” (node name/hostname). I usually do it by using the node name:
    1. To lookup the node name, go to the printer, press the Menu button, select “4. Network”, “2. WLAN”, “1. TCP/IP”, and “5. Node Name”. (Alternatively, the wireless router’s DHCP client table should have the printer’s hostname which is the same as the node name.)
    2. Back in the Brother setup dialog, select “Specify your machine by name” and input the node name.
    3. Click Next.
  10. The installation program will take several minutes to install the various Brother driver and tools.
  11. Click Next and Next to skip the “User’s Guides” and “On-Line Registration”.
  12. I usually uncheck “Enable Status Monitor on startup” and leave the “Set as Default Printer” checked. Click Next.
  13. The setup will request a reboot.
  14. After the reboot, you will see a new, red “CC4″ icon in the status tray. This is the Brother Control Center software which allows you to set device properties, print, and scan. Because I prefer using my own programs to scan, I usually remove this from the tray by doing the following:
    1. Right-click on the CC4 icon and select “Preferences”.
    2. Unselect “Start ControlCenter on computer startup”.
    3. Hit the OK button.
    4. Right-click the CC4 icon and select “Close”.
  15. (OPTIONAL) Even though I have configured the Brother software to not run Control Center and the Status Monitor (unchecked “Enable Status Monitor on startup” in last page of installation wizard), Brother still runs them stealthily on startup. To really get rid of them, I had to do the following:
    1. Run “msconfig”.
    2. Select Startup tab.
    3. Under Windows 7, uncheck “Brother ControlCenter” and “Brother Status Monitor Application”.
    4. Under Windows XP, uncheck “BrCcBoot” and “BrStMonW”.
    5. Click Apply and then click OK.
    6. You may be prompted to restart.

To configure Windows to use Toner Save Mode by default:

  1. Go to menu “Start->Control Panel”.
  2. On Windows XP:
    1. Click on “Printers and Other Hardware”.
    2. Click on “View installed printers or fax machines”.
    3. Right-click on printer and select “Printer Preferences” to open the “Brother HL-2280DW Printer Printing Preferences” dialog.
  3. On Windows 7:
    1. Click on “View devices and printers”.
    2. Double-click on the Brother printer to open it.
    3. Double-click “Adjust print options” to open the “Brother HL-2280DW Printer Printing Preferences” dialog.
  4. In the Printer Preferences dialog:
    1. Select the Advanced tab.
    2. Check the “Toner Save Mode” option.
    3. Hit the Apply button and then the OK button.

The built-in way to do a scan on Windows XP:

  1. Run “Start->All Programs->Accessories->Scanner and Camera Wizard”.
  2. The Brother printer will be listed at the top. Click Next.
  3. Click on Preview, select options, and click Next.
  4. Select output format and folder. Click Next.
  5. The scan will be taken and saved to the “My Pictures” folder by default.

The built-in way to do a scan on Windows 7:

  1. Run “Windows Fax and Scan”.
  2. Click the “New Scan” button in the top toolbar.
  3. Hit Preview to see a preview image.
  4. Select the options and hit Scan.
  5. The scan will be taken and saved to the “Documents\Scanned Documents” folder by default.

Though I refer specifically to the Brother HL-2280DW, these instructions may apply to other wireless printers.

40 Responses
  1. nick :

    Date: August 25, 2012 @ 11:15 am

    what good is a wireless printer if i have to plug it in. how do i use its wirelessly?

  2. Chanh :

    Date: August 25, 2012 @ 11:23 am

    Hi Nick,

    We just need to plug in the Ethernet cable to setup the printer. Once the printer is configured, we can unplug the Ethernet cable and move the printer to anywhere since it is now wireless connected.

    Regards.

  3. Teresa :

    Date: September 19, 2012 @ 8:41 pm

    This was a great help! Thanks for taking the time to do this documentation. You da bomb!

  4. Estrella :

    Date: September 20, 2012 @ 3:18 pm

    I am able to print wirelessly to this printer via my PC, however, my iPhone does not recognize it. Any suggestions?

  5. Chanh :

    Date: September 22, 2012 @ 12:04 am

    Hi Estrella,

    Unfortunately, the Brother HL-2280DW does not support Apple AirPrint to support printing directly from an iOS device like an iPhone. However, you could run an AirPrint server on a Windows machine, to which the iPhone can print to and which then in turn, prints to the Brother printer. The downside is that you have to make sure the Windows machine is on and running the AirPrint server whenever you wish to print from your iPhone.

    Hope that helps. Cheers.

  6. Asia :

    Date: November 25, 2012 @ 5:11 pm

    Sorry, I am confused about three things.

    1. Where do I find my router channel number? (I am on a MacBook Pro with Qwest router)

    2. Re step 5 “Browse to the printer’s assigned IP address to access its web interface” — browse where? From my Internet? I found the IP address by going through the step in #4, but When I enter that in Google, I just get weird links.

    3. Re step 7. Configure the wireless network access:

    7. 1 Click on “Network Configuration” link at the top.

    Where is this Network COnfiguration? I’m on a MacBook Pro.

    Thank you for any help you can provide.

  7. Asia :

    Date: November 25, 2012 @ 5:40 pm

    Nick,

    This is Asia again — Never mind. I think I have figured it out (after 3 hrs ;-)

    Thank you for your blog.

  8. Chanh :

    Date: December 21, 2012 @ 1:29 pm

    Hi Nick,

    I’m glad you figured it out. Just in case others might run into the same issues, I’ll attempt to answer your original questions. (Please feel free to add your inputs.)

    [1. Where do I find my router channel number? (I am on a MacBook Pro with Qwest router)]
    The router’s wireless channel number can be found by logging into the router and looking at its wifi configuration; it will be a number between 1-13. Alternatively, you can install and run inSSIDer, a free wireless scanning tool that will let you know what channel your router is broadcasting on.

    [2. Re step 5 “Browse to the printer’s assigned IP address to access its web interface” — browse where? From my Internet? I found the IP address by going through the step in #4, but When I enter that in Google, I just get weird links.]
    If your printer’s IP address is 192.168.1.55, then open up a browser like IE, Chrome, Firefox, etc. and input “http://192.168.1.55/” into the address bar.

    [3. Re step 7. Configure the wireless network access: 7. 1 Click on “Network Configuration” link at the top. Where is this Network COnfiguration? I’m on a MacBook Pro.]
    This is referring to the header at the top of the printer’s admin web page which you would have browsed to in step #5.

    Regards, Chanh

  9. W. E. Peterson :

    Date: January 15, 2013 @ 12:58 pm

    My Brother HL-2280dw is hardwired to my desktop. Can I also connect it to my ipad wireless while keeping the hardwire to my desktop?

  10. Chanh :

    Date: January 15, 2013 @ 7:54 pm

    Hi W.E.,

    As long as your computer devices are connected (wired or wirelessly) to the same router that the printer is connected to, the devices should be able to reach and use the printer.

    Unfortunately, the Brother HL-2280DW does not support Airprint, which is the printing protocol used by iPad and iPhone. However, you can get partial printing and scanning to work by installing and using the free Brother iPrint&Scan app.

    For those who have Android phones or tablets, there is a free Android version of Brother iPrint&Scan.

    Hope that helps.
    - Chanh

  11. Leo :

    Date: February 1, 2013 @ 8:51 am

    Cannot find where scanned documents are stored on Mac osX, although when scan to email, they open on outlook. Can anyone help.

  12. Chanh :

    Date: February 1, 2013 @ 10:21 pm

    Hi Leo,

    By default, the Mac OS X scanner’s utility will save the scanned images to the “Pictures” directory. On the scanner’s details dialog, look for the field named “Scan To”. It should be populated with the “Pictures” folder by default. You can change it to be whatever folder you want to store the scans to.

    Regards.

  13. Ron :

    Date: February 20, 2013 @ 10:35 pm

    Great work, thanks for this excellent guide.

  14. Jake Peters :

    Date: March 2, 2013 @ 5:44 pm

    I have an iMac and the Brother 2280DW printer, connected via an ethernet cable.

    When I try to check the wired IP address, by doing:

    “Select the following menu items by pressing the up/down arrows and clicking on the OK button:

    4. Network
    1. Wired LAN
    1. TCP/IP
    2. IP Address ”

    The address is 0.0.0.0, even after “re-booting” the printer. Do I need a cross-over ethernet cable?

    Maybe the iMac ethernet port is not enabled?

    Thanks,

    JP

  15. Chanh :

    Date: March 2, 2013 @ 6:35 pm

    Hi Jake,

    If your printer is connected to a router or switch, then you don’t need a cross-over Ethernet cable. Usually cross-over cables are only required if you want to connect two computers directly together.

    I suggest resetting the printer to factory default configuration. Search in the post for “reset the printer” to find instructions on how to reset your printer. In factory configuration, the printer’s Ethernet port will be enabled by default.

    Regards.

  16. Jake Peters :

    Date: March 2, 2013 @ 6:59 pm

    Thank you Chanh,

    I am directly connecting the printer and the iMac (well, my Mom is. I’m helping remotely). Some newer ethernet devices have some type of auto-sense on the transmit/receive lines so a cross-over cable is not required.

    I was wondering if this printer had that capability.

    I haven’t tried resetting yet (it is brand new, just out of the box), but so far the above instructions for either the wired or wireless have not yet succeeded.

    I may have to use the software, but it looks like Mac OS X Mountain Lion (10.8) requires a download, which is relatively complicated for my Mom.

    Thanks again,

    Pete

  17. Chanh :

    Date: March 2, 2013 @ 7:41 pm

    Hi Jake,

    It sounds like your mom doesn’t have a wired or wireless router for Internet access. If she did, you could connect the printer to that and keep the iMac wireless connected. Without a router to provide dynamically assigned addresses (DHCP) and coordinate the communication, it is probably best to just connect the printer to the iMac using a USB cable.

    Otherwise, if you are directly connecting the printer and the iMac using an Ethernet cable, then you should use a cross-over cable. I think the auto-sense is usually on ports of a hub or switch device, not on the client like a printer or an iMac. Then, you will need to manually configure both the printer and the iMac to have different static IP addresses. Finally, you should be able to browse to the printer’s static IP address from the iMac.

    I haven’t configured a static IP address for the printer before so am not sure how to go about it. Without the router, you would have to keep the iMac and the printer connected by the cross-over Ethernet cable in order for your mom to print and scan. This would be the same as keeping the two connected with a USB cable though. I think using USB cable would be the easier option.

    Good luck with setting up the printer for your mom.

  18. Jake Peters :

    Date: March 2, 2013 @ 7:49 pm

    Chanh,

    Thanks again.

    She does have wireless internet access and was using it during our troubleshooting.

    I was able to get the printer to print out the network settings and it did have an WLAN IP address when she chose her SSID from the printer.

    However, she could not see the printer from Safari, for some reason.

    It could be that there is a problem with some configuration on the printer side (above instructions show initial printer config for wireless via a wired connection – that probably failed for my Mom because she does not have a cross-over cable).

    Maybe I can get her to re-do the wireless config (but I fear that the 16 digit key will be the stumbling block).

    Thanks again,

    Jake

  19. MG :

    Date: March 8, 2013 @ 1:26 pm

    Thanks Chanh. This was very helpful.

  20. Ian :

    Date: July 23, 2013 @ 6:02 pm

    oh. em. gee! ok, so, i think of myself as a tech savvy enough-ish person. I mean, i even worked at apple (as a concierge, not really techie or sales) for a little while! still, installing this printer was terrible because of that silly cd thing. and random drivers and blah blah. really, thank you so much for your step by step instructions!

  21. Rob :

    Date: August 29, 2013 @ 6:23 pm

    This is excellent. I have two questions.

    The printer software install puts an icon on the menu bar for the Brother Control Center that leads to menu for Scanning. It worked when wired over ethernet but now wireless this method of scanning does not work. It is much quicker initiating a scan than going through system preferences. When I try it now wirelessly I get Unable to Launch Target Application…
    (CC001)

    Also how do you do multipage scans?

  22. Rob :

    Date: August 29, 2013 @ 6:25 pm

    Sorry, I am on Snow Leopard.

  23. Chanh :

    Date: August 30, 2013 @ 3:11 am

    Hi Rob,

    If you switch from wired to wireless, or vice versa, you will need to remove the printer and re-add it on Mac OS X. On Windows, you would need to remove the printer, uninstall the driver, re-install the driver, and select wireless/network mode (instead of wired USB).

    To do multi-page scan, you’ll need a printer with the document feeder. Then in the scan dialog’s Scan Mode, select Document Feeder instead of Flatbed.

    Hope that helps, Chanh

  24. Rob :

    Date: August 30, 2013 @ 6:09 am

    Thanks Chanh, I tried removing the printer and re-adding it. That got the printer to print. I did get it to scan most times via the System Preferences Print & Fax method (thanks again), but when it was wired I could to scan via the Control Center which was much faster.

    I do have an HP printer that I use for only multipage scans. The printer is useless as a printer because the ink dries out after a few weeks and HP supplies are brutally expensive. It is flatbed like this HL-2280DW but the HP software will ask if there is a second page and make multi-page scanned PDFs. Nice software — when it works. I am now beginning to assume that the HL-2280 DW does not have that software feature. If I could get this brother to scan better I would re-cycle the HP to clear up some space in my crowded office.

  25. Peter Hartshorn :

    Date: September 11, 2013 @ 10:10 am

    Chahn, thank you so much for taking the time to post this! It helped immensely. I too got snagged by the inability to enter in the full 16 digit hex code for the wep key on the LCD and was pulling my hair out trying to get this onto the network properly. If (as is my case) you are putting this onto a wireless network with an older router (i.e. no “push button security setup”) getting this printer onto your network is far from trivial. Thanks again.

  26. Chanh :

    Date: September 11, 2013 @ 10:23 am

    Hi Rob,

    Glad that it partially addressed your needs. Concerning the Brother Control Center for Mac OS X, I found a helpful website, Brother Control Center installs & disappears. Based on that page, I would suggest doing following:

    • Look for the “Library/Printers/Brother/Utilities/ControlCenter” directory. The Control Center app “controlcenter.app” may already exist there since you used to have it working.
    • Or if you don’t have the Control Center app already, install the latest TWAIN driver for your Brother printer.
      1. Browse to Brother’s OS X Mountain Lion Support Statement page.
      2. Locate your printer model in the list of models near bottom and click on the corresponding “>Go” link to the right.
      3. Select your location and OS X version.
      4. Search for “TWAIN” and you should find a section named “Scanner Driver (TWAIN)” or similar. The description for it should say something like “This Scanner Driver includes the Brother ControlCenter software for easy to use one button scanning from your Mac or machine Scan-to button”.
      5. Download the TWAIN driver.
      6. I think you should remove the printer before installing the TWAIN driver.

    Good luck, Chanh

  27. Steve :

    Date: September 11, 2013 @ 7:07 pm

    Hi, Chahn. Thanks for this site! I have my HL-2280DW connected via Ethernet to a desktop pc via a wireless router. We also have a laptop pc in the house and I’d love to print wirelessly from the laptop. The Quick Setup Guide that came with the printer says, “Although the Brother HL-2280DW can be used in both a wired and wireless network, only one of the connection methods can be used at a time.” Is the thing I want to do the thing the manual says can’t be done? Or is this the correct interpretation: each individual PC can only be set up to connect one way: wired or wireless. I just don’t know which interpretation is correct and would love to find out what’s possible before messing up stuff and wasting time trying to do impossible things. Thanks for your knowledge on this subject!

  28. Chanh :

    Date: September 12, 2013 @ 2:53 am

    Hi Steve,

    Hopefully I can make the instructions more understandable. The latter interpretation is correct; you will configure your computer to use only one of the connectivity options.

    You can have your computer connected to the printer either by wire (connected by USB cable) or by network (supposing your printer is connected to the network by network cable or by wireless). When adding and installing the printer software on your computer, you will need to select either the USB or network installation option.

    On Windows, when you install the Brother printer software, you’ll be asked to select USB or network drivers. If you pick USB driver, your computer has to be physically connected to the printer by USB cable in order for you to print and scan. If you pick network, you’ll need to select or input the printer’s network name or IP address. If you have installed the USB driver and wish to switch to the network driver, you would need to uninstall the printer software, re-install it, and select the network option.

    On the Mac, you don’t need to install and uninstall the printer software because the Mac OS X will do that for you when you add and remove printers. When you add the printer, you can select USB or network. If you select network, the Mac software will usually show a lists of printers accessible on the network which you can select for installation.

    Regards, Chanh

  29. Chanh :

    Date: September 19, 2013 @ 9:03 pm

    Hi Rob,

    I found out that you could do a multi-page scan using the default Mac OS X scan utility. In the detailed scan dialog, select the Format as “PDF” and then check the “Combine into single document” option underneath. From then on, anything you scan will be added to the PDF specified by the Name field. Once you are done, just modify the Name field or rename the PDF file using the Finder.

    Mac OS X Scan Dialog - Multipage PDF

    Hopefully the above works for you and will allow you to free up some space in your office.

    Regards, Chanh

  30. Donna :

    Date: December 2, 2013 @ 11:16 pm

    Thanks for your blog. I just bought the printer and felt like a dumb-dumb because I couldn’t figure out how to set up the wireless printing (as others have mentioned, that was the whole point of purchasing a wireless printer). Thanks to your blog, I was actually able to get the dang thing connected wirelessly (too bad I had already spent about 4 hours beating it like a cavewoman).

    Unfortunately, when I try to print, the printer keeps pausing all the print jobs automatically. I hit “resume,” it thinks for a little bit, then it pauses itself again. What’s the deal?!?!?!

    Sincerely yours,
    Printer Luddite

  31. Chanh :

    Date: December 2, 2013 @ 11:55 pm

    Hi Donna,

    I haven’t seen the pause all jobs behavior. I did a google search but came up empty for Brother printers. Here’s my troubleshooting suggestions in order from easy to a lot of work:

    1. Check the printer permissions. Go to control panel to see the list of printers. Right-click on the printer and select Printer Properties. Click on the Security tab. Make sure that the “Print” permission is checked for “Everyone”. If it isn’t already checked, then this is probably the cause.
    2. Uninstall the Brother software, reboot the computer and printer, and re-install the Brother software.
    3. Call Brother support to ask for help. It might be a hardware defect.

    I’ll be crossing my fingers for you.
    Chanh

  32. Donna :

    Date: December 13, 2013 @ 4:46 pm

    Chanh, thank you so much for your prompt response! I ended up just purchasing a USB cord. Turns out, the two days it took the cord to ship was still less time than it took for me to try to figure out how to sync up the wifi! :)

    I appreciate your help!

    Warmly,
    =Donna

  33. sharon :

    Date: December 31, 2013 @ 4:53 pm

    After an entire weekend, I finally installed the brother hl-2280dw via ethernet connection to my router. Got my pc to work wirelessly as well as added this printer to my MacBook Pro. Now I have the Brother Status monitor pop-up, “failed to connect to the device” message, and “Getting Status” progress pop-up frozen on the screen. The three pop-ups won’t close. What can I do to delete this application?

  34. Chanh :

    Date: January 6, 2014 @ 7:56 am

    Hi Sharon,

    Glad that you got it working. Concerning getting rid of the status monitor, you can do so using the “msconfig” application which comes with Windows. Just search in this post for “msconfig” and you’ll find the optional instructions to disable launching the Brother utilities on Windows startup.

    Happy belated holidays!

  35. Mike :

    Date: March 15, 2014 @ 11:28 pm

    Chanh,

    Great pointers for those printers. For some reasons I found it ackward to have to use a USB connection to set up the wireless function but did it nonetheless. Got up and running within 30 minutes. Now, I cannot get my iPhone not iPad to detect the printer despite using iPrint&Scan as you suggested.

    Thank you,

    Mike

  36. Chanh :

    Date: March 18, 2014 @ 8:43 pm

    Hi Mike,

    Glad you got it working using the USB connection method. I’m not sure how the iPrint & Scan app works but most likely, it is looking for Brother printers on the same wireless network. You might want to browse to your router’s web interface and see if the printer is listed under the list of DHCP clients. That will tell you that the printer is visible on the network. If the printer is visible on the wireless network, then the problem is with the iPrint & Scan app.

    Good luck.

  37. Linda :

    Date: May 12, 2014 @ 1:27 pm

    I just brought the wireless Brother hl-2280 to wanted to print coupons from the coupons app on my ipad but unfortunately it can not locate up my printer. Why is that can anybody help me out. I can print on my laptop but not on my ipad. Just trying to save some more mkney by printing these coupons out you know.

  38. Chanh :

    Date: May 12, 2014 @ 6:32 pm

    Hi Linda,

    Unfortunately, the Brother HL-2280 does not support AirPrint, which supports printing from iOS devices like iPads. However, there is a workaround.

    To print from the iPad, you will need to install the Brother iPrint&Scan iOS app, free from the iTunes store. The Brother iPrint&Scan app will allow you to print to the Brother HL-2280 wireless printer. Once you have the app installed on your iPad, go to the coupons app page, and copy the contents of that page. Then run the Brother iPrint&Scan app, select the clipboards tab (or something like that), you should see the coupons page that you copied, and then print from that.

    Regards, Chanh

  39. Jack Tran :

    Date: June 9, 2014 @ 8:26 pm

    Thank you for documenting your process! I followed your instructions exactly and it worked!

  40. Jay R. Parr :

    Date: August 10, 2014 @ 11:07 pm

    Thank You! Thank you!
    I recently bought a new ASUS router and it said it was not compatible with my new(ish) Brother 2280. I was so disappointed. I looked around the Internet off and on for days with varying opinions. Today I decided to take a shot at it. Did a Google search and for the first time saw your site. IT WORKED PERFECTLY.

    Now I have two Mac-minis, a new iPad, MacBook AND my 2280 printer all wireless thru this lovely ASUS RT-N56U router. I feel like a new man, instead of a burned out 70 year old computer engineer who knows nothing anymore.

    Ottawa Canada

Leave a Comment

Your comment

You can use these tags: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Please note: Comment moderation is enabled and may delay your comment. There is no need to resubmit your comment.